Explosion-Proof Motors for Saudi Plants: Ex d, Ex e, Ex n

15.11.26 08:25 AM

In short: an explosion-proof motor is defined by its certificate, not its paint. Ex d, Ex e, Ex n and Ex t motors protect against different ignition risks and are selected by zone, gas group and temperature class. BTGC supplies WEG medium and high voltage motors for hazardous areas in Saudi Arabia, with IECEx and ATEX certificates, and services them at the WEG approved service center in Jubail.

WEG industrial electric motor supplied by BTGC in Saudi Arabia

Most motors in a Saudi refinery, gas plant or petrochemical complex sit inside a hazardous area. Pump and fan motors near flanges, agitators on solvent tanks, compressor auxiliaries and loading pump motors all have to be built so that a fault inside the motor cannot ignite the gas outside it. The buyer's job is to match the motor's protection concept to the area classification, and to make sure the certificate covers the exact motor that arrives.

Protection concepts, in plain terms

MarkingConceptTypical use
Ex db (flameproof)The frame contains an internal explosion and cools the escaping gas through flame pathsZone 1, pumps and compressors in process units
Ex eb (increased safety)No arcs or hot spots in normal or defined fault conditions; strict tE time and protection relayZone 1 fans and pumps where a lighter motor is wanted
Ex ec (non-sparking)No ignition source in normal operationZone 2, the majority of plant motors
Ex tb / tc (dust)Dust-tight enclosure with limited surface temperatureZone 21/22, sulphur, polymer powder and grain handling

After the concept comes the gas group (IIA, IIB or IIC; hydrogen service needs IIC) and the temperature class (T3 at 200 °C is the usual refinery requirement, T4 at 135 °C for some solvents). A motor marked Ex db IIB T4 Gb is not acceptable where hydrogen is present, however good it is.

Variable speed drives and Ex motors

Running an Ex motor on a VFD changes its thermal behaviour: at low speed the shaft fan moves less air, and the drive's harmonics add losses. The certificate must state that the motor is approved for inverter duty, with the speed range, the drive type and usually a requirement for embedded thermistors wired to a certified protection relay. WEG certifies its hazardous-area motors for inverter duty where specified and supplies the embedded thermal protection, which saves an argument with the site inspector later.

The certificate is the product

Saudi operators accept IECEx certificates, and most also accept ATEX; SASO conformity and the operator's own vendor approval come on top. Each motor must carry a nameplate with the certificate number and the full marking, and the certificate must cover the frame size, the terminal box and any cable gland or accessory fitted. Three things BTGC checks before a motor is released to site:

  • The certificate number on the nameplate matches the IECEx online register.

  • The gas group and temperature class meet the area classification drawing, not just the data sheet.

  • Cable glands and plugs carry their own Ex certification; a flameproof motor with an uncertified gland is a non-conformity.

Large electric motor stator under repair in the BTGC motor workshop in Jubail

Repairing an Ex motor without losing the certificate

A flameproof motor repaired in a workshop that does not control flame-path gaps is no longer flameproof. IEC 60079-19 sets the rules for repair and overhaul of Ex equipment: measured flame paths, approved winding insulation systems, documented tests and a repair plate. The BTGC service center in Jubail is the WEG approved service center in Saudi Arabia and follows the WEG repair procedures for Ex motors, so a rewound Ex motor goes back with its certification intact and a repair record the operator can file.

WEG from BTGC

WEG builds medium and high voltage motors for hazardous areas in flameproof (Ex db), increased-safety (Ex eb), non-sparking (Ex ec) and pressurised (Ex p) designs, with IECEx and ATEX certification and inverter-duty options. BTGC covers WEG medium and high voltage motors and drives in the Kingdom: BTGC is the WEG partner in Saudi Arabia and runs the WEG approved service center in Jubail. See the electrical and power systems page and the oil and gas sector page.

Questions buyers ask

Can we fit an Ex ec motor in Zone 1 to save cost? No. Zone 1 needs Ex db or Ex eb; the area classification drawing decides, not the budget.

Is a repaired Ex motor still certified? Only if the repairer works to IEC 60079-19 and documents the flame paths and winding system; ask for the repair report.

What should an enquiry include? Zone, gas group, temperature class, ambient temperature (50 °C in the Eastern Province is normal), duty, mounting, voltage and whether a VFD is used.

Contact the BTGC power division

Email power@btc-ksa.com or call +966 13 856 0528. Branches: Dammam, Jubail and Yanbu. Request a quote.