Hazardous-Area Plugs and Sockets for Saudi Rigs and Plants

15.11.26 08:30 AM

In short: a plug and socket in a Zone 1 or Zone 2 area must be certified as a complete unit, must not be separated under load and must survive heat, salt and rough handling. Marechal Electric DXN explosion-proof plugs and sockets use butt contacts and an integral switch so they can be certified for hazardous areas and still be safe to operate. BTGC supplies them in Saudi Arabia for rigs, terminals, refineries and petrochemical plants.

Marechal Electric DECONTACTOR plugs, sockets and connectors supplied by BTGC

Portable and mobile equipment is everywhere in a hazardous plant: welding sets during turnarounds, temporary pumps, heaters, lighting, mobile compressors, and the maintenance tools that follow them. Each one needs a connection point, and in a classified area that connection point is an electrical apparatus in its own right, with its own certificate and its own failure modes.

What makes a connector hazardous-area rated

  • Certification as an assembly: plug, socket and enclosure are certified together under IEC 60079; a certified socket with an uncertified plug is not a certified connection.

  • No separation under load: either an interlock prevents withdrawal while energised, or the device switches off before the contacts separate. Marechal's DECONTACTOR design does the second: the plug is a load-break switch, so there is no arc at the contacts when it is withdrawn.

  • Enclosure protection: Ex db (flameproof) or Ex eb (increased safety) with Ex d switching components; IP66/67 against dust and washdown; corrosion-resistant metal or glass-fibre reinforced polyester bodies for the coast.

  • Temperature class: the surface temperature in operation must stay below the T class of the area, which limits current rating at 50 °C ambient.

Butt contacts versus pin and sleeve

CharacteristicPin and sleeveMarechal butt contact
Contact pressureSpring sleeve, weakens with wear and heatSpring-loaded face contact, constant pressure
Sand and dustCollects in the sleeve, raises resistanceSelf-cleaning wiping action on the contact face
Making and breakingArc at the pins if withdrawn under loadSwitching inside the device, silver-nickel contacts rated for the load
Heat riseHigher at full load, matters for T classLower resistance, lower temperature rise

Where they go in a Saudi plant

  • Drilling rigs: rig floor and mud pit outlets for pumps, lights and tools in Zone 1 and 2.

  • Terminals and jetties: shore power for tankers and barges, portable pump connections.

  • Refinery and petrochemical turnarounds: welding and tool outlets in process units, where temporary cabling is heavy and connections are made and broken daily.

  • Motor disconnects: a DECONTACTOR at each motor in a hazardous area gives a visible, lockable isolation point, as described in the earlier article on switch-rated plugs for motor disconnection.

Lock-out, tag-out

Hazardous-area connectors also carry the safety isolation role. A DECONTACTOR socket with a padlockable lid or a lock-off accessory gives the maintenance crew a single point to isolate and lock a machine without opening a switchboard, which is how most Saudi operators now run their LOTO procedures for portable and semi-fixed equipment.

Electric motor under service at the BTGC workshop in Jubail

Marechal Electric from BTGC

Marechal Electric SAS, France, invented the DECONTACTOR and manufactures the DXN hazardous-area range with ATEX and IECEx certification, from 16 A to 250 A, alongside its industrial DS and DSN ranges and high-current DX connectors. BTGC is the Marechal Electric partner in Saudi Arabia, holding common ratings in Dammam and supporting rig, terminal and plant projects. See the electrical and power systems page and the drilling and rig solutions page.

Questions buyers ask

Can an industrial DECONTACTOR be used in Zone 2? No. Zone 2 needs the certified DXN range; the industrial ranges are for safe areas.

What rating for welding sets? Usually 63 A or 125 A at 400 V; BTGC checks the duty cycle and ambient derating.

Are spare parts available locally? Contacts, lids and glands for common sizes are held in Dammam.

Contact the BTGC power division

Email power@btc-ksa.com or call +966 13 856 0528. Branches: Dammam, Jubail and Yanbu. Request a quote.