In short: hospitals, data centers, desalination plants and process units all depend on standby power, and many sites bring in portable generators during outages or connect load banks to test their own sets. When those connections are made by bolting cables onto busbars, every hook-up takes hours, needs a live-working risk assessment and invites phase rotation errors. A permanent generator connection point with switch-rated sockets turns the job into a plug-in operation. BTGC supplies Marechal Electric DECONTACTOR plugs, sockets and high-current connectors for this duty.

In the Saudi summer, a lost grid supply or a failed standby generator is not an inconvenience: chillers, process cooling and life-safety systems stop. Planned work on switchgear and transformers also needs temporary generators. The weak point is often not the generator itself but the time and risk of connecting it.
Why bolted connections are a problem
Time. Opening a panel, terminating cables and testing can take hours, during which the load is without supply.
Exposure. Electricians work inside switchboards that may have adjacent live sections.
Errors. Phase rotation mistakes reverse motors and pumps; loose lugs overheat under full load in high ambient temperature.
Repeat cost. The same work is repeated for every outage and every generator test.
A permanent connection point
The usual solution is a generator connection cabinet wired permanently to the switchboard or transfer switch, with a set of sockets on the outside. The portable generator or load bank arrives with matching plugs on its cables and is connected without opening any panel. Interlocks keep the sockets dead until the plug is fully engaged and prevent the generator from back-feeding the grid.
| Option | Advantages | Limits |
|---|---|---|
| Single-pole cam-type connectors | High current per pole, flexible cable arrangements | Each pole is connected separately, so phase sequence and live-unplugging risks remain unless interlocked |
| Multi-pole switch-rated plugs and sockets | Correct phase sequence by design, switching action in the plug, no arc at the contacts | Current per plug is limited, so large generators use several in parallel |
| Bolted terminations | No connector cost | Slow, needs a panel opened, highest risk |
What switch-rated means
A switch-rated plug such as the DECONTACTOR has spring-loaded butt contacts and a built-in switching mechanism, so it can make and break load current safely, and it cannot be withdrawn while live. The same principle is explained for motors in switch-rated plugs for motor disconnection and for shutdown work in temporary power for turnarounds.

Designing the connection point
Rate sockets and cables for the generator's full output with derating for ambient temperature and solar gain.
Where currents are high, use separate connectors for phases, neutral and earth with mechanical coding so they cannot be swapped.
Interlock the box with the transfer switch so the generator cannot back-feed the grid or parallel with another source unintentionally.
Choose enclosures with an IP rating suitable for dust and wash-down, and certified versions inside hazardous areas.
Label the box with rating, phase sequence and the procedure, and keep matching plugs with the site and rental generator fleet.
Load bank testing
Standby diesel generators that run lightly for years build up carbon and unburnt fuel in the exhaust, a condition called wet stacking. Periodic load bank tests at a meaningful share of rated output keep the engine healthy and prove the set can carry the load. A plug-in load bank connection makes those tests routine instead of an engineering job, which is why it is often installed together with the generator connection point.
Marechal Electric from BTGC
Marechal Electric makes DECONTACTOR switch-rated plugs and sockets for industrial and hazardous areas, and high-current connectors for generators and mobile equipment. BTGC is the Marechal Electric partner in Saudi Arabia. See also hazardous-area plugs and sockets and the electrical power systems page.
Questions buyers ask
Can one plug carry the full output of a large generator? Large generators usually connect through several plugs or high-current connectors in parallel; BTGC sizes the arrangement from the generator rating.
Can a connection point be retrofitted to an existing switchboard? Usually yes, through a spare feeder or the transfer switch; the design must be approved by the site's electrical authority.
Do you supply the generator-side plugs as well? Yes. Matching plugs and cable assemblies can be supplied for site generators, rental fleets and load banks.
Contact the BTGC power division
Email power@btc-ksa.com or call +966 13 856 0528. Branches: Dammam, Jubail and Yanbu. Request a quote.