Fire Pumps for Saudi Industrial Plants: NFPA 20 Choices and Testing

17.11.26 09:37 AM

In short: a fire pump has one job: deliver its rated flow and pressure every time it is called, often after years on standby. NFPA 20 sets how fire pumps are built, listed, installed and accepted, and NFPA 25 sets how they are tested in service. The pump type follows the water source: split case and end suction pumps need water at positive pressure, while vertical turbine pumps lift from tanks, pits and the sea. BTGC supplies Pentair Aurora and Fairbanks Nijhuis fire pumps, UL listed and FM approved, with electric or diesel drive and complete packages.

Pentair Aurora horizontal split case fire pump

Refineries, petrochemical plants, power stations, terminals, warehouses and new industrial cities in the Kingdom all depend on fire water systems. Owners apply NFPA 20 together with local requirements such as the Saudi Fire Code (SBC 801), Civil Defense approval and company standards, for example Saudi Aramco SAES-B-017 for fire water system design. Getting the pump choice right at the start avoids expensive changes at acceptance testing.

What NFPA 20 asks of a fire pump

  • The pump is listed for fire service (UL listed, FM approved) and selected for a rated flow and rated pressure.

  • Its curve must stay within set limits: at 150 per cent of rated flow it must still give at least 65 per cent of rated pressure, and its shutoff (churn) pressure must not exceed 140 per cent of rated pressure.

  • Controllers, drivers, relief valves, test headers and flow meters are part of the system and must be listed and arranged as the standard requires.

  • A jockey pump keeps the system pressurised so the main pump starts only on a real demand.

Choosing the pump type

TypeWater sourceTypical use
Horizontal split casePositive suction from a tank or mainMost plant fire water systems; easy access to rotating parts
Vertical split casePositive suctionSame duties where floor space is tight
Vertical turbineBelow the pump: pits, wells, reservoirs or the seaSeawater fire water at coastal plants, terminals and jetties
End suction and vertical in-linePositive suctionSmaller flows in buildings and support facilities

Pentair Aurora packaged systems cover, for example, horizontal split case pumps from about 250 to 5,000 gpm and vertical turbine pumps from about 500 to 4,500 gpm, with special materials available for seawater service.

Pentair vertical turbine pump for below-grade water sources

Electric or diesel drive

  • Electric motors are simple and need little attention, but need a reliable supply that stays live during a fire; many sites add a second source or an automatic transfer switch.

  • Diesel engines make the pump independent of the plant power system and are common in Saudi industrial plants, often as one of two or more pumps.

  • In hot climates, check engine cooling, fuel tank temperature and room ventilation; diesel rooms in the Kingdom often reach high temperatures in summer.

Testing and keeping pumps ready

  • Factory and field acceptance tests: the pump is run at churn, rated flow and 150 per cent flow and the results compared with the certified curve.

  • Routine churn runs: NFPA 25 sets regular no-flow runs, weekly for diesel-driven pumps, with readings recorded each time.

  • Annual flow test: a full-flow test confirms the pump still meets its curve; falling results usually point to wear ring wear, a blocked suction or impeller damage.

  • Spares: keep wear rings, bearings, seals or packing and diesel engine service parts in stock, because a fire pump out of service may require a fire watch.

Pentair fire pumps from BTGC

BTGC is the Pentair partner in Saudi Arabia for Aurora and Fairbanks Nijhuis fire pumps, jockey pumps, controllers and spare parts. Valves for fire water systems are covered in fire-safe valves, and motor care in electric motor bearing grease. See the pumps and rotating equipment page and the petrochemicals sector page.

Questions buyers ask

Can an existing fire pump be replaced like for like? Usually yes, if the replacement is listed for the same rated flow and pressure and the suction, discharge and driver arrangement suit it. Send BTGC the nameplate, curve and test records.

Which pump suits a seawater fire water system? A vertical turbine pump in seawater-resistant materials is the usual choice, because the water level is below the pump.

Does BTGC supply complete packages? Yes. Pentair packaged fire pump systems combine the pump, driver, controller, jockey pump and accessories.

Contact BTGC

Email info@btc-ksa.com or call +966 13 856 0528. Branches: Dammam, Jubail and Yanbu. Request a quote.