Wastewater Lift Station Pumps: Solids Handling, Chopper and Ragging

17.11.26 09:45 AM

In short: lift stations move sewage and industrial wastewater from low points to treatment, and their pumps face rags, wipes, grit, grease and hydrogen sulphide. Submersible solids handling pumps cover most duties; chopper and grinder pumps cut solids that would otherwise wrap impellers; vortex pumps tolerate stringy and gritty flows at lower efficiency. Wet well design, controls and corrosion protection matter as much as the pump. BTGC supplies Pentair Hydromatic, Myers and Fairbanks Nijhuis wastewater pumps.

Pentair Hydromatic submersible solids handling pump

New cities, industrial zones and expanding municipal networks in the Kingdom are adding lift stations every year, and industrial cities such as Jubail and Yanbu run their own wastewater systems. High temperatures speed up the formation of hydrogen sulphide in sewers, and modern wipes have made ragging the most common cause of pump call-outs worldwide.

Choosing the pump type

TypeHow it handles solidsBest for
Non-clog (enclosed or semi-open impeller)Large free passage, typically 3 inch solids or more for raw sewageMost municipal and industrial lift stations; best efficiency
ChopperCutting edges on the impeller and a cutter bar chop rags and solidsStations with heavy ragging, wipes, food or industrial solids
GrinderMacerates solids into a slurry before pumpingSmall flows, pressure sewers, single buildings
Vortex (recessed impeller)Solids pass through a vortex without touching the impellerStringy or gritty flows where efficiency matters less
Self-priming (dry mounted)Pump sits above the wet wellEasy access stations and temporary duties

Fighting ragging

  • Pick impellers designed for modern flushables, or chopper pumps on problem stations; Pentair Hydromatic offers solids handling pumps designed for this duty.

  • Avoid long running at low flow, which lets rags build up; variable speed controls can add short reverse or high-speed cleaning cycles.

  • Screen or macerate upstream of critical stations.

  • Record call-outs by station to see where a different pump type pays back.

Pentair Hydromatic chopper pump for ragging wastewater

Wet well and station design

  • Size the wet well volume for the allowed motor starts per hour, so pumps neither short-cycle nor sit too long.

  • Keep minimum submergence above the pump to avoid vortices and motor overheating.

  • Use guide rail systems so pumps can be lifted out without entering the well.

  • Fit check valves and isolation valves suitable for sewage, such as ball check valves and knife gate valves.

  • Ventilate and treat odour; hydrogen sulphide attacks concrete and steel and is a serious safety hazard.

Materials and motors

  • Cast iron is standard; stainless steel or special alloys for corrosive industrial wastewater.

  • Double mechanical seals with moisture sensing protect the motor.

  • Explosion-proof motors are often required in wet wells classified as hazardous areas; see explosion-proof motors.

  • Plug connectors make portable and emergency pumps quick to change, see plug connections for submersible pumps.

Pentair wastewater pumps from BTGC

BTGC is the Pentair partner in Saudi Arabia for Hydromatic, Myers and Fairbanks Nijhuis wastewater pumps and spare parts. Sludge handling is covered in sludge dewatering. See the power and utilities sector and pumps pages.

Questions buyers ask

Can a submersible pump run dry? Not for long. Keep the stop level above the pump's minimum submergence and use motor protection.

When should we change to chopper pumps? When a station needs frequent de-ragging despite good operation; the extra cost is usually recovered quickly in fewer call-outs.

Can BTGC replace pumps from another maker on the same guide rails? Often, with an adapter; send BTGC the existing pump data and the guide rail details.

Contact BTGC

Email info@btc-ksa.com or call +966 13 856 0528. Branches: Dammam, Jubail and Yanbu. Request a quote.